Kecepatan Penarikan Kawat NiTi pada Sifat Mekanis dalam Proses Wire Drawing
Keywords:
NiTi, Round Variation, Wire DrawingAbstract
Abstract - To get a strong wire and not easily broken or broken, you must use a wire with a large diameter. This is certainly not efficient because it will spend a lot of wire in the production process. Therefore, manufacturers carry out wire drawing which is a wire drawing process with the aim of getting a strong wire and wire diameter as desired. In this study, a test will be carried out which aims to analyze the effect of variations in motor rotation speed on the mechanical properties of NiTi in the wire drawing process with grease added with detergent. In this research, wire drawing process was carried out, hardness test to determine wire hardness, and metallographic test to see wire surface. Speed variations are used in the wire drawing process as measurement parameters that will affect the specimen results. The result of this research is that the lower the speed of wire drawing in the wire drawing process, the mechanical properties of NiTi wire will increase in terms of strength, stiffness, hardness, and reduced wire ductility.References
Asfarizal, Pengaruh Variasi Sudut Dies Terhadap Penarikan Kawat Alumunium . Jurnal. Teknik Mesin Vol.2, No. 1, Oktober 2012 : 41-48.
Aziz Nur Eva. Analisis Sifat Fisis Dan Mekanis Alumunium Paduan Al-Si-Cu Dengan Menggunakan Cetakan Pasir. Skripsi. Jurusan Teknik Mesin Fakultas Teknik Universitas Muhammadyah. Surakarta.2012.
Bajameter, 2021 Alat Uji Kekerasan Tembaga dan Logam Brinnel Hardness Testes TBBCM, https://bajameter.com/alat-uji-kekerasan-tembaga-logam-brinell-hardness-tester-tbbcm/Fajar Nugroho. Pengaruh Rapat Arus Dan Waktu Anodizing Terhadap Laju Keausan Permukaan Pada Alumunium Paduan AA 2024-T3. Journal. Journal Foundry Vol. 4 No. 1 April 2014 ISSN : 2087-2259 (Diakses pada 21 Januari 2021).
Firman, 2013:Analisis Kekuatan Tarik dan Kekasaran Kawat Tembaga Hasil Drawing akibat Variasi Persentase Reduksi,JurnalRotor, Volume 6 Nomor 1,JurusanTeknikMesin, Fakultas Teknik, Universitas Jember (UNEJ).
Halimatus Sa’diyah Hasyim “Pengaruh Perendaman Kawat Nikel Titanium Termal Ortodonti Dalam Minuman The Kemasan Terhadap Gaya Defleksi Kawat ( The Effect Of Immersion Thermal Nikel-Titanium-Archire In The Botted Dtea Drink To The Archiwire Force Deffection )” Fakultas Kedokteran Gigi Vol 5 No 2 Universitas Jember 21 Mei 2017.
M. Bahar Fitrianto, Pengujian Koefisien Gesek Permukaan Plat Baja St 37 Pada Bidang Miring Terhadap Viskositas Pelumas Dan Kekerasan Permukaan. Jurnal. Momentum, Vol. 11, No. 1, April 2015, Hal. 13-18.
M. Hasan Abdullah1), Optimasi perencanaan produksi wire drawing menggunakan mixed integer linear programming (studi kasus di pt. Sw) Volume XIX No.2, Maret 2019, p.09-22 Teknik Industri Universitas Wijaya Putra.
Mohammad Firman, Mahros Darsin, Hari Arbiantara B, Analisis Kekuatan Tarik dan Kekasaran Kawat Tembaga Hasil Drawing akibat Variasi Persentase Reduksi, JurnalROTOR, Volume 6 Nomor 1 Januari 2013.
Putri Arifiani dan Erwin Siregar, Karakteristik kawat TMA (titanium molybdenum 2016; 2(3): 163-171.
Pusat Lingkaran, 2017 Pengujian Kekerasan Pada Mesin Vickers Manual. http://pusat-lingkaran.blogspot.com/2017/06/pengujian-kekerasan-bahan-pada-mesin.html?m=1 (Diakses pada 21 januari 2021).
